WH23X38617 Genuine OEM GE Washer Drain Pump Filter with Seal
The WH23X38617 is a Genuine OEM GE replacement drain pump filter with seal, compatible with select GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo models. The pump filter sits inside the drain pump housing and traps lint, coins, hair, and small debris before they reach the pump impeller. Keeping this filter clean and intact is essential for proper drainage — a clogged or damaged filter causes slow draining, standing water in the tub, and can strain the drain pump over time.
This genuine OEM part is manufactured by GE to factory specifications and includes both the pump filter and the seal. The seal prevents leaks at the pump clean-out when the filter is installed correctly. The filter body is blue plastic with rubber seal components, measuring approximately 6" L x 3" W x 3" H. It directly replaces part number AP7243923 and installs with a simple counterclockwise removal and clockwise installation — no special tools required.
Quick Answer
The WH23X38617 Genuine OEM GE Washer Drain Pump Filter with Seal fixes GE washers that drain slowly, leave standing water in the tub, or leak near the pump access panel. The filter traps lint and debris to protect the pump impeller. Includes filter and seal. Blue plastic/rubber, approx. 6" L x 3" W x 3" H. Twist-out installation — no tools needed. Compatible with GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo models.
Common Problems This Part Fixes
- Washer draining slowly or not draining at all after a wash cycle
- Standing water remaining in the drum at the end of a cycle
- Water leaking from the pump filter access panel at the front of the washer
- Error codes related to drain or pump failure on compatible GE models
- Unusual noise from the drain pump caused by debris reaching the impeller
- Cracked, stripped, or missing filter cap allowing debris into the pump housing
- Damaged or deteriorated seal causing leaks at the filter access port
Replaces Part Numbers
This drain pump filter directly replaces the following part numbers:
WH23X38617, WH23X38617, FIX17874614, AGE1014282, PD00090185, AP7243923, PS17874614.
Contact our support team with your model number if you need help confirming compatibility before ordering.
Compatibility
This drain pump filter is compatible with select washers and laundry centers from the following GE product lines:
- GE front-load washers (select models)
- GE Profile front-load washers (select models)
- GE 2-in-1 Washer/Dryer Combo (select models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
- Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance
- Traps lint, coins, hair, and small debris to protect the drain pump impeller from damage
- Includes both the pump filter and seal — everything needed for a complete replacement
- Seal prevents water leaks at the pump filter access port when the filter is properly installed
- Blue plastic and rubber construction — durable and chemical resistant
- Dimensions: approximately 6" L x 3" W x 3" H
- Twist-out installation — turns counterclockwise to remove, clockwise to install; no special tools required
- Should be cleaned regularly (every 1–3 months) and replaced when cracked, stripped, or leaking
Product Specifications
| Part Number | WH23X38617 |
| Part Type | Washer Drain Pump Filter with Seal |
| Condition | Genuine OEM |
| Application | Front-load washers and 2-in-1 washer/dryer combos |
| Approximate Dimensions | 6" L x 3" W x 3" H |
| Color | Blue |
| Material | Plastic / Rubber |
| Includes | Pump filter and seal |
| Installation | Twist-out / twist-in — no special tools required |
| Compatible Brands | GE, GE Profile |
Installation Notes
Frequently Asked Questions
What does the drain pump filter do?
The drain pump filter catches lint, coins, hair, buttons, and other small items before they can reach the drain pump impeller. Without the filter, debris can jam or damage the impeller — leading to pump failure, loud grinding noises, or a washer that won't drain. The filter also acts as a cleanout access point so you can periodically remove accumulated debris without disassembling the pump.
How often should I clean or replace the pump filter?
GE recommends cleaning the pump filter every 1–3 months depending on how frequently you run the washer and how much lint your laundry produces. The filter should be replaced rather than just cleaned if it is cracked, stripped at the threads, or if the seal is damaged or missing — a compromised filter or seal will leak water from the access port.
Why is water leaking from the front of my GE washer near the bottom?
A leak at the lower front of the washer near the pump access panel is most often caused by a damaged or deteriorated pump filter seal, a cracked filter body, or a filter that is not fully tightened. Replacing the WH23X38617 pump filter and seal resolves this in most cases. Make sure the new filter is hand-tightened snugly — do not overtighten, as this can crack the housing.
Will there be water when I remove the pump filter?
Yes — there is always residual water in the drain pump housing. Before removing the filter, place towels and a shallow pan or tray directly under the access panel to catch the water. The amount varies depending on how much water remains in the washer after the last cycle. Running a drain-only cycle immediately before removing the filter will minimize the amount of water released.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same pump filter and seal that GE installs in compatible models from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
